User Contributed                                            MET/CAL Procedure
=============================================================================
INSTRUMENT:            Unholtz-Dickie OSC-1S:Sweep Sine Generator
DATE:                  09-Sep-97
AUTHOR:                User Contributed                                               
REVISION:              0
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       24
NUMBER OF LINES:       294
CONFIGURATION:         HP 34401A
CONFIGURATION:         HP 5335A
CONFIGURATION:         HP 8903A
=============================================================================
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  ASK-   R     N              P             M              F        W
  1.002  ASK+                                          X
  1.003  HEAD         INITIAL CONDITIONS
  1.004  DISP         Make sure power is removed before proceeding.
  1.005  DISP         Remove top cover and place the A-OSC
  1.005  DISP         board (Sweep Light Control) on an extender.
  1.006  DISP         Connect the HP 5335A counter INPUT A to the 220 ohm
  1.006  DISP         resistor by the red "U".  Reapply power
  1.007  DISP         Set the UUT as follows:
  1.007  DISP         LOWER LIMIT ........................ Full ccw
  1.007  DISP         UPPER LIMIT ........................ Full cw
  1.007  DISP         SWEEP TIME ......................... 1.0 min
  1.007  DISP         NO. OF SWEEPS ...................... 01
  1.007  DISP         RANGE Hz ........................... 2-2k
  1.007  DISP         SAMPLE RATE ........................ LO
  1.008  HEAD         {* Oscillator Tests *}
  1.009  HEAD         { Accuracy }
  1.010  HEAD         * Oscillator Tests *
  1.011  JMP          2.001
  1.012  EVAL
  2.001  DISP         Connect the HP 34401A DMM to the J19 OUTPUT
  2.001  DISP         connector on the UUT.
  2.002  DISP         Depress the MAN button and adjust the
  2.002  DISP         COARSE and FINE controls for a reading of 5 Hz.
  2.003  IEEE         [@34401]FUNC "VOLT:AC"
  2.004  IEEE         [@34401]DET:BAND 3
  2.005  ACC    10    1.250V         0.035% 0.03/
  2.006  HEAD         [27][91]7m[27][91]5mPlease Wait ...... Long Measurement
  2.007  IEEE         [@34401]READ?[I]
  2.008  MEME
  2.009  HEAD
  2.010  MEMC         V              3%            5H
#!          Test Tol 0.0375, Sys Tol 0.0003325, TUR 112.782 (>= 4.00).
  3.001  DISP         Adjust the COARSE and FINE controls for
  3.001  DISP         a reading of 50 Hz.
  3.002  IEEE         [@34401]FUNC "VOLT:AC"
  3.003  IEEE         [@34401]DET:BAND 20
  3.004  ACC    10    1.250V         0.06% 0.03/
  3.005  IEEE         [@34401]READ?[I]
  3.006  MEME
  3.007  HEAD
  3.008  MEMC         V              3%            50H
#!          Test Tol 0.0375, Sys Tol 0.0002075, TUR 180.723 (>= 4.00).
  4.001  DISP         Adjust the COARSE and FINE controls for
  4.001  DISP         a reading of 500 Hz.
  4.002  IEEE         [@34401]FUNC "VOLT:AC"
  4.003  ACC    10    1.250V         0.06% 0.03/
  4.004  IEEE         [@34401]READ?[I]
  4.005  MEME
  4.006  HEAD
  4.007  MEMC         V              3%            500H
#!          Test Tol 0.0375, Sys Tol 0.0001825, TUR 205.479 (>= 4.00).
  5.001  DISP         Set the UUT as follows:
  5.001  DISP         RANGE Hz ........................... 5-5k
  5.002  DISP         Adjust the COARSE and FINE controls for
  5.002  DISP         a reading of 5000 Hz.
  5.003  IEEE         [@34401]FUNC "VOLT:AC"
  5.004  ACC    10    1.250V         0.06% 0.03/
  5.005  IEEE         [@34401]READ?[I]
  5.006  MEME
  5.007  HEAD
  5.008  MEMC         V              3%            5000H
#!          Test Tol 0.0375, Sys Tol 0.0002075, TUR 180.723 (>= 4.00).
  6.001  HEAD         {}
  6.002  HEAD         { Sweep Time }
  6.003  JMP          7.001
  6.004  EVAL
  7.001  DISP         Press the UPPER LIMIT RESET, and adjust the UPPER
  7.001  DISP         limit for 5k Hz.
  7.002  DISP         Press the LOWER LIMIT RESET button on the UUT.
  7.002  DISP         Adjust the LOWER LIMIT for 5 Hz.
  7.003  JMP          7.006
  7.004  DISP         Press the LOWER LIMIT RESET button in the UUT.
  7.004  DISP         Wait for the UUT's counter to settle at 5 Hz.
  7.005  IEEE         [@5335]IN; [D2000]
  7.006  IEEE         [TERM LF]
  7.007  IEEE         [@5335]FN2,CO1,AS1,BS0,TR1,AT.3,BT3;
# 7.006  IEEE         [@5335]FN2,AS1,BS0;
  7.008  IEEE         [@5335]RE;
  7.009  DISP         Depress the SWEEP button.  The UP light should be lit.
  7.010  OPBR         Is the counter's gate light on?
  7.011  JMPF         7.004
  7.012  HEAD         [27][91]5m**THIS MEASUREMENT TAKES ONE MINUTE**[27][91]m
  7.013  IEEE         [@5335][T0][I]
  7.014  HEAD
  7.015  ACC          60.00T         100P%
  7.016  MEME
  7.017  MEMC         T              1.00U         up
#!          Test Tol 1, Sys Tol 0.006, TUR 166.667 (>= 4.00).
  8.001  MATH         MEM1=MEM-MEM1
  8.002  JMPZ         8.004          1U
  8.003  JMP          7.004
  8.004  DISP         Move the input to CH A on the counter to the resistor
  8.004  DISP         with the red "D".
  8.005  DISP         Press UPPER sweep reset limit button on the UUT.
  8.006  JMP          8.008
  8.007  DISP         Press the UPPER LIMIT RESET button in the UUT.
  8.007  DISP         Wait for the UUT's counter to settle at 5 kHz.
  8.008  IEEE         [@5335]RE;
  8.009  DISP         Depress the SWEEP button on the UUT.
  8.009  DISP         The DOWN light should be lit.
  8.010  OPBR         Is the counter's gate light on?
  8.011  JMPF         8.007
  8.012  HEAD         [27][91]5m**THIS MEASUREMENT TAKES ONE MINUTE**[27][91]m
  8.013  IEEE         [@5335][T0][I]
  8.014  HEAD
  8.015  ACC          60.00T         100P%
  8.016  MEME
  8.017  MEMC         T              1.00U         down
#!          Test Tol 1, Sys Tol 0.006, TUR 166.667 (>= 4.00).
  9.001  MATH         mem1=mem-mem1
  9.002  JMPZ         9.004          1U
  9.003  JMP          8.007
  9.004  DISP         Set the UUT as follows:
  9.004  DISP         SWEEP TIME ......................... 10.0 min
  9.005  DISP         Move the CH A input to the resistor with the red "U".
  9.006  DISP         Press the LOWER LIMIT RESET button in the UUT.
  9.006  DISP         Wait for the UUT's counter to settle at 5 Hz.
  9.007  IEEE         [@5335]RE;
  9.008  DISP         Depress the SWEEP button.  The UP light should be lit.
  9.009  OPBR         Is the counter's gate light on?
  9.010  JMPF         9.006
  9.011  HEAD         [27][91]5m*THIS MEASUREMENT TAKES TEN MINUTES*[27][91]m
  9.012  IEEE         [@5335][T0][I]
  9.013  HEAD
  9.014  ACC          600.00T        100P%
  9.015  MEME
  9.016  MEMC         T              12.00U        up
#!          Test Tol 12, Sys Tol 0.06, TUR 200.000 (>= 4.00).
 10.001  MATH         MEM1=MEM-MEM1
 10.002  JMPZ         10.004         12U
 10.003  JMP          9.006
 10.004  DISP         Move the CH A input to the resistor with the red "D".
 10.005  DISP         Press UPPER sweep reset limit button on the UUT.
 10.006  JMP          10.008
 10.007  DISP         Press the UPPER LIMIT RESET button in the UUT.
 10.007  DISP         Wait for the UUT's counter to settle at 5 kHz.
 10.008  IEEE         [@5335]RE;
 10.009  DISP         Depress the SWEEP button on the UUT.
 10.009  DISP         The DOWN light should be lit.
 10.010  OPBR         Is the counter's gate light on?
 10.011  JMPF         10.007
 10.012  HEAD         [27][91]5m*THIS MEASUREMENT TAKES TEN MINUTES*[27][91]m
 10.013  IEEE         [@5335][T0][I]
 10.014  HEAD
 10.015  ACC          600.00T        100P%
 10.016  MEME
 10.017  MEMC         T              12.00U        down
#!          Test Tol 12, Sys Tol 0.06, TUR 200.000 (>= 4.00).
 11.001  MATH         mem1=mem-mem1
 11.002  JMPZ         11.004         12U
 11.003  JMP          10.007
 11.004  HEAD         {}
 11.005  HEAD         { Linear Frequency Output }
 11.006  JMP          12.001
 11.007  EVAL
 12.001  DISP         Remove power from the UUT, disconnect the
 12.001  DISP         counter and return the circuit card to the motherboard.
 12.002  DISP         Reconnect the power to the UUT and connect
 12.002  DISP         the DMM to the LIN FREQ output.  Connect the counter
 12.002  DISP         CH A to the OSC output on the UUT.
 12.003  IEEE         [@5335]FN9,RE;
 12.004  DISP         Press the MAN button on the UUT adjust the COARSE and
 12.004  DISP         FINE controls for a reading of 200.00mS on the counter.
 12.005  IEEE         [@34401]FUNC "VOLT:DC"
 12.006  IEEE         [@34401]VOLT:DC:RANG:AUTO ON
 12.007  ACC    100   10.00mV        .005% .0035/
 12.008  IEEE         [@34401]READ?[I]
 12.009  MEM*         1000
 12.010  MEME
 12.011  MEMC         mV             2.00U         5H
#!          Test Tol 2, Sys Tol 7.01e-005, TUR 28530.670 (>= 4.00).
 13.001  DISP         Adjust the COARSE and FINE controls for a reading
 13.001  DISP         of 20.00mS on the counter.
 13.002  IEEE         [@34401]FUNC "VOLT:DC"
 13.003  IEEE         [@34401]VOLT:DC:RANG:AUTO ON
 13.004  ACC    100   100.00mV       .005% .0035/
 13.005  IEEE         [@34401]READ?[I]
 13.006  MEM*         1000
 13.007  MEME
 13.008  MEMC         mV             2.00U         50H
#!          Test Tol 2, Sys Tol 0.0007001, TUR 2856.735 (>= 4.00).
 14.001  IEEE         [@5335]FN1,RE;
 14.002  DISP         Adjust the COARSE and FINE controls for a reading
 14.002  DISP         of 500.00Hz on the counter.
 14.003  IEEE         [@34401]FUNC "VOLT:DC"
 14.004  IEEE         [@34401]VOLT:DC:RANG:AUTO ON
 14.005  ACC    1     1.000V         .004% .0007/
 14.006  IEEE         [@34401]READ?[I]
 14.007  MEME
 14.008  MEMC         V              0.020U        500H
#!          Test Tol 0.02, Sys Tol 6.4e-006, TUR 3125.000 (>= 4.00).
 15.001  DISP         Adjust the COARSE and FINE controls for a reading
 15.001  DISP         of 5000.0Hz on the counter.
 15.002  IEEE         [@34401]FUNC "VOLT:DC"
 15.003  IEEE         [@34401]VOLT:DC:RANG:AUTO ON
 15.004  ACC    10    10.000V        .0035% .0005/
 15.005  IEEE         [@34401]READ?[I]
 15.006  MEME
 15.007  MEMC         V              0.200U        5000H
#!          Test Tol 0.2, Sys Tol 6.2e-005, TUR 3225.806 (>= 4.00).
 16.001  HEAD         {}
 16.002  HEAD         { Log Frequency Output }
 16.003  JMP          17.001
 16.004  EVAL
 17.001  IEEE         [@5335]FN9,RE;
 17.002  DISP         Connect the HP 34401A DMM to the LOG FREQ
 17.002  DISP         output on the UUT.
 17.003  IEEE         [@34401]FUNC "VOLT:DC"
 17.004  IEEE         [@34401]VOLT:DC:RANG:AUTO ON
 17.005  DISP         Adjust the COARSE and FINE controls for a
 17.005  DISP         reading of 200.00mS on the counter.
 17.006  IEEE         [@34401][T0]READ?[I]
 17.007  ACC    100   0.0000mV       .005% .0035/
 17.008  MEME
 17.009  MEMC         mV             4.00U         5H
#!          Test Tol 4, Sys Tol 1e-007, TUR 40000000.000 (>= 4.00).
 18.001  IEEE         [@34401]FUNC "VOLT:DC"
 18.002  IEEE         [@34401]VOLT:DC:RANG:AUTO ON
 18.003  DISP         Adjust the COARSE and FINE controls for a
 18.003  DISP         reading of 20.00mS on the counter.
 18.004  IEEE         [@34401]READ?[I]
 18.005  ACC    1     .4000V         .004% .0007/
 18.006  MEME
 18.007  MEMC         V              0.004U        50H
#!          Test Tol 0.004, Sys Tol 2.8e-006, TUR 1428.571 (>= 4.00).
 19.001  IEEE         [@5335]FN1,RE;
 19.002  IEEE         [@34401]FUNC "VOLT:DC"
 19.003  IEEE         [@34401]VOLT:DC:RANG:AUTO ON
 19.004  DISP         Adjust the COARSE and FINE controls for a
 19.004  DISP         reading of 500.00Hz on the counter.
 19.005  IEEE         [@34401]READ?[I]
 19.006  ACC    1     .8000V         .004% .0007/
 19.007  MEME
 19.008  MEMC         V              0.004U        500H
#!          Test Tol 0.004, Sys Tol 5.2e-006, TUR 769.231 (>= 4.00).
 20.001  IEEE         [@34401]FUNC "VOLT:DC"
 20.002  IEEE         [@34401]VOLT:DC:RANG:AUTO ON
 20.003  DISP         Adjust the COARSE and FINE controls for a
 20.003  DISP         reading of 5000.00Hz on the counter.
 20.004  IEEE         [@34401]READ?[I]
 20.005  ACC    10    1.2000V        .0035% .0005/
 20.006  MEME
 20.007  MEMC         V              0.0040U       5000H
#!          Test Tol 0.004, Sys Tol 7.6e-006, TUR 526.316 (>= 4.00).
 21.001  HEAD         {}
 21.002  HEAD         { Distortion Tests }
 21.003  JMP          22.001
 21.004  EVAL
 22.001  DISP         Connect UUT J19 OUTPUT connector to the HP 8903A
 22.001  DISP         Distortion Analyzer INPUT HIGH BNC.
 22.002  DISP         With the UUT in MAN mode, adjust the FINE and COARSE
 22.002  DISP         controls for 300Hz.
 22.003  IEEE         [@8903][TERM LF]
 22.004  IEEE         [@8903]M3
 22.005  IEEE         [@8903]LN
 22.006  IEEE         [@8903][I]
 22.007  ACC          .50percent     0.015U
#22.007  MATH         mem1=0
#22.007  MEME
 22.008  MEMC         0.00percent    0.500U        300H
#!          Test Tol 0.5, Sys Tol 0.015, TUR 33.333 (>= 4.00).
 23.001  DISP         On the UUT, adjust the FINE and COARSE
 23.001  DISP         controls for 3kHz.
 23.002  IEEE         [@8903][TERM LF]
 23.003  IEEE         [@8903]M3
 23.004  IEEE         [@8903]LN
 23.005  IEEE         [@8903][I]
 23.006  ACC          .50percent     0.015U
#23.007  MATH         mem1=0
#23.007  MEME
 23.007  MEMC         0.00percent    0.500U        3kH
#!          Test Tol 0.5, Sys Tol 0.015, TUR 33.333 (>= 4.00).
 24.001  DISP         Disconnect all equipment from UUT and remove power.
 24.002  END
#! T.U.R.s less than 4.00:                  0
#! T.U.R.s estimated using RANGE value:     0
#! T.U.R.s not calculated (ASK- U):         0
#! T.U.R.s not computable at compile time:  0
#! FOR JUSTIFICATION REFER TO COMMENTS FOLLOWING EACH TEST IN THIS LISTING.